O’Conner Formula: The Simple Conservative 1RM Estimate

The O’Conner formula (1989) is the simplest 1RM equation worth knowing: 1RM = weight × (1 + reps ÷ 40). It’s Epley’s quieter cousin — same linear shape, gentler slope — and it consistently returns the most conservative estimates of the major formulas. When you’d rather underestimate your max than overestimate it, this is your formula.

What is the O’Conner formula?

oconner formula
oconner formula

Published in 1989, O’Conner takes the same linear approach as Epley but divides by 40 instead of 30. That one change — a smaller slope — means every rep adds less to the estimate. From 100 kg:

  • 1 rep → 102.5 kg
  • 5 reps → 112.5 kg
  • 10 reps → 125.0 kg
  • 15 reps → 137.5 kg

Here’s a neat fact: at exactly 5 reps, O’Conner gives 112.5 — identical to Brzycki’s 112.5. Two completely different formulas (one linear, one rational) converging on the same number isn’t a coincidence so much as both being reasonable models of the same physiology at that rep range. Past 5 reps they diverge: at 10, Brzycki says 133.3 while O’Conner says 125.0.

How does the O’Conner math actually work?

The formula is 1RM = W × (1 + R/40), where W is weight and R is reps.

That’s it. No exponents, no Euler’s number, no denominator that shrinks toward zero. Each rep adds exactly 2.5% of the lifted weight to the estimate. Five reps adds 12.5%. Ten reps adds 25%. You can do it in your head between sets, which is genuinely useful — not every formula needs to be a research instrument. Sometimes you just want a quick sanity check on what you lifted.

The linearity is both the strength and the limitation. Real rep-to-max relationships aren’t perfectly linear — they curve — which is why the exponential formulas exist. But over the 1–10 rep range where you should be testing anyway, the linear approximation is close enough that the simplicity is worth it.

Worked example: 135 lb for 10 reps

  1. Weight = 135, reps = 10
  2. 10 ÷ 40 = 0.25
  3. 1 + 0.25 = 1.25
  4. 135 × 1.25 = 168.75
  5. Estimated 1RM: 168.8 lb

Compare: Epley says 180.0 and Brzycki says 180.0 from that set (they’re identical at 10). O’Conner’s 168.8 is more than 11 lb lower. That’s the conservatism in action — and frankly, for a 10-rep set, I find O’Conner’s number more believable. Ten reps is far enough from a single that the aggressive formulas start flattering you.

Another: 200 lb for 8 reps.

  1. 8 ÷ 40 = 0.20; 1.20 × 200 = 240.0
  2. Estimated 1RM: 240.0 lb

Epley would give 253.3 here. The gap between “simple and conservative” and “standard” is about 13 lb — meaningful for programming, which is exactly when the choice matters.

Where does O’Conner shine?

Beginners. This is O’Conner’s best use case, full stop. New lifters’ technique is still developing, their true max is a moving target, and an aggressive estimate just sets them up to attempt weights they can’t handle safely. A conservative formula keeps training weights in the productive zone while strength builds fast underneath. I’d rather a beginner train off 240 when their “true” max is 250 than train off 260.

Programming training maxes. Wendler’s 5/3/1 famously has you train off 90% of your max. Starting from an O’Conner estimate instead of an Epley one is like building in an extra margin — your percentages land where you can actually complete the work, which is the entire point of submaximal training.

Quick mental math. 2.5% per rep is doable in your head. 185 for 6? That’s 15% over 185, so roughly 213. (Calculator says 212.8. Close enough for a between-sets check.) Try doing Wathan in your head and get back to me.

Where does it struggle?

It leaves pounds on the table for experienced lifters. If you’re an advanced lifter with a well-calibrated sense of your capabilities, O’Conner’s conservatism becomes a limitation — you’ll consistently test above it, which means your programmed percentages run light. At that stage, Epley or a personal calibration factor serves you better.

High reps stay linear. The formula doesn’t know that 15 reps is a different physiological event than 5. At very high reps it keeps adding 2.5% per rep in a straight line while reality curves. Cap inputs at 10 reps like you should be doing anyway.

How does O’Conner compare to Epley and Brzycki?

O’Conner is Epley with the volume turned down. Same shape, smaller slope: where Epley adds 3.33% per rep, O’Conner adds 2.5%. At 5 reps from 100 kg: Epley 116.7, O’Conner 112.5, Brzycki 112.5.

At 10 reps the conservative gap opens: Epley/Brzycki 133.3, O’Conner 125.0 — an 8.3 kg difference, about 6%.

At 15 reps: Brzycki 163.6, Epley 150.0, O’Conner 137.5. O’Conner is the most conservative of the three by a wide margin, and interestingly it’s in the same neighborhood as Lombardi’s 131.1 — the two “careful” formulas arriving at similar places by completely different routes.

Think of it this way: Epley tells you what you might be capable of, O’Conner tells you what you can definitely handle. For programming, the second number is usually the more useful one.

Frequently asked questions

Is the O’Conner formula accurate?

It’s accurate in the sense that matters: it rarely overpromises. In the 3–8 rep range its estimates sit slightly below Epley’s, which for training purposes is a feature. It was included in LeSuer et al.’s 1997 validation study of seven equations, so it’s a legitimate published formula, not gym folklore.

Why is O’Conner always lower than Epley?

Smaller slope — 1/40 per rep instead of 1/30. Every rep adds 2.5% instead of 3.33%. Over 10 reps that compounds to a meaningful gap (125.0 vs 133.3 from 100 kg). It’s a design choice, not an error.

Should I use O’Conner instead of Epley?

If you’re a beginner, programming conservatively, or doing mental math between sets — yes. If you’re experienced and want the most likely number rather than the safest one, Epley or a multi-formula consensus is the better call.

At 5 reps O’Conner equals Brzycki — is that a coincidence?

It’s arithmetic, not coincidence: at r=5, O’Conner gives 1+5/40 = 1.125 and Brzycki gives 36/(37−5) = 36/32 = 1.125. Two different curves crossing at one point. They diverge everywhere else, so don’t mistake it for equivalence.

Sources

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *